Loading vehicle data from NHTSA...
NHTSA recalls, safety ratings, and consumer complaints for the 1999 Ford Crown Victoria.
| Trim | City | Hwy | Combined | Annual fuel $ |
|---|---|---|---|---|
| 4.6L 8 cyl Automatic 4-spd | 15 | 22 | 18 | $3,300 |
| Overall Rating | Not Rated |
| Frontal Crash | Not Rated |
| Side Crash | Not Rated |
| Rollover | Not Rated |
Component: STEERING
Dorman Products, Inc. (Dorman) is recalling certain model Dorman Steering Shafts, part number 425-359, Solutions Steering Shafts, part number 7-0359, and OE Solutions Steering Shafts, part number 425-359, manufactured April 17, 2014, to September 28, 2015. These aftermarket replacement steering shafts are sold for use in 1995-2002 Ford Crown Victoria, Mercury Grand Marquis, and Lincoln Town Car vehicles. These steering shafts may separate during operation if the integral fastener is loose or missing and if the interfacing vehicle shaft is compressed in length.
Consequence: If the shafts separate during vehicle operation, a loss of steering control would result, increasing the risk of a vehicle crash.
Remedy: Dorman will notify owners, and dealers will replace the steering shaft, free of charge. The recall began on October 28, 2015. Owners may contact Dorman customer service at 1-800-523-2492, option 5.
Component: FUEL SYSTEM, GASOLINE
CERTAIN AFTERMARKET FUEL FILTERS SOLD UNDER THE PUROLATOR BRAND NAME, P/N F65277, SHIPPED FROM JANUARY 16 THROUGH JUNE 2, 2006, FOR USE ON THE ABOVE LISTED PASSENGER VEHICLES. DUE TO INCORRECT DESIGN, THE QUICK CONNECTORS MAY NOT FULLY SEAT WITH THE TUBE INTERFACE, EVEN THOUGH THE PERSON MAKING THE CONNECTION MAY BELIEVE THAT THE QUICK CONNECTOR IS FULLY ATTACHED.
Consequence: FAILURE OF THIS CONNECTION COULD LEAD TO FUEL SPILLAGE AND, IN THE PRESENCE OF AN IGNITION SOURCE, A FIRE COULD OCCUR.
Remedy: UFI WILL NOTIFY OWNERS AND REPLACE THE FILTERS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 4, 2006. OWNERS MAY CONTACT UFI FILTERS USA AT 800-230-5876.
My 99 ford crown victoria lx has front end issues. I have had to replace the ball joints about 4 times every 2 to 3 months because the front end keeps dropping. I'm not sure if you guys know about this but I've spoken with our local Ford mechanic and a few friends who have crown Victoria's as well and said that it has been a big issue with them along with the electrical components for the turn signals
WHEN DRIVING ON THE INTERSTATE AT 75 MPH THE EXTERIOR LIGHTS AS WELL AS THE DASH LIGHTS SHUT OFF. THEY THEN CAME BACK ON AFTER ABOUT A MINUTE AND A HALF. THE LIGHTS INTERMITTENTLY SHUT OFF AND COME BACK ON AT RANDOM. I CAN BE ON THE INTERSTATE OR ON A CITY STREET. I CAN BE GOING FORWARD OR BACKWARDS WHEN THIS HAPPENS. THIS IS A HUGE SAFETY ISSUE.
THE TURN SINGLE COMMILM IS MESSING UP.THE WIPERS WILL NOT WORK
THE PAD KEY STOP WORKING I HAD TO CALL MY INSURANCE COMPANY TO LET ME IN MY CAR ON A RAINY NITE WITH MY KIDS N TILL THIS DAY STILL DON'T WORK.I CAN'T LICK MY DOORS
The 1999 Ford Crown Victoria has 8 NHTSA recalls and 164 consumer complaints on file. It received an overall safety rating of Not Rated out of 5 stars in NHTSA crash testing. The high number of complaints suggests potential reliability concerns — review the complaint details above before purchasing. For the most detailed information about a specific vehicle, decode its VIN using our free decoder above.
Enter a specific VIN to get the full report — specs, recalls, safety ratings, complaints, investigations, and technical service bulletins.
Component: EQUIPMENT:MECHANICAL:INTEGRATED JACK/LEVELER/STABILIZER
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES HAVE JACKING INSTRUCTIONS WHICH, IF FOLLOWED, COULD CAUSE THE VEHICLE OPERATOR TO PLACE THE JACK ON A FRAME WELD WHEN ATTEMPTING TO RAISE A REAR WHEEL. IF THE VEHICLE IS JACKED UP WITH THE JACK PLACED ON THE FRAME WELD AND IF THE VEHICLE IS FREE TO ROLL (WHEELS NOT BLOCKED OR CHOCKED), THE JACK COULD YIELD AND THE VEHICLE MAY DROP SUDDENLY.
Consequence: IF THIS OCCURS AND ANY PORTION OF THE OPERATOR'S BODY IS UNDER THE VEHICLE, THE POTENTIAL FOR PERSONAL INJURY EXISTS.
Remedy: OWNERS WILL BE PROVIDED WITH A REVISED JACK INSTRUCTION AND STOWAGE CARD AND JACK WARNING LABEL, AS WELL AS A SUPPLEMENT TO THE OWNER GUIDE.
Component: SEAT BELTS:FRONT:ANCHORAGE
VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET FRONT PASSENGER SIDE SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.
Consequence: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.
Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.
Component: FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY
IN ORDER TO ENHANCE POLICE OFFICE SAFETY, MODEL YEAR 1992-2003 CROWN VICTORIA POLICE INTERCEPTOR (CVPI) VEHICLES WILL BE EQUIPPED WITH SHIELDS DESIGNED TO HELP PROTECT THE FUEL TANK IN HIGH-SPEED REAR-IMPACT CRASHES. FORD ALSO WILL BE OFFERING AN OPTIONAL TRUNK PACKAGE DESIGNED TO IMPROVE THE SAFE TRANSPORT OF SHARP-EDGED, HEAVY EQUIPMENT IN THESE VEHICLES.
Consequence: SOME HIGH-SPEED REAR-IMPACT CRASHES HAVE RESULTED IN FUEL TANK PUNCTURES AND FIRES IN CVPI VEHICLES.
Remedy: FORD HAS ADVISED US THAT SHIELD KITS HAVE BEEN AVAILABLE SINCE LATE OCTOBER AND WILL BE INSTALLED ON POLICE INTERCEPTOR VEHICLES AT NO COST. THE OPTIONAL TRANK PACKAGE WILL BE AVAILABLE BY THE END OF 2002. FORD HAS ESTABLISHED A NEW WEB SITE AT WWW.CVPI.COM TO ANSWER ADDITIONAL QUESTIONS ABOUT THE SAFE USE OF CPVI VEHICLES.
Component: FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY
ON CERTAIN NATURAL GAS VEHICLES, IF A FLAME FROM A VEHICLE INTERIOR FIRE BECOMES LOCALLY DIRECTED AT THE NATURAL GAS FUEL TANK LOCATED IMMEDIATELY BEHIND THE REAR SEAT, THE FLAME COULD DAMAGE THE FIBERGLASS WRAP ON THE TANK WEAKENING THE TANK.
Consequence: IF THE STRENGTH OF THE TANK IS SIGNIFICANTLY COMPROMISED, IT COULD RUPTURE, INCREASING THE RISK OF A FIRE.
Remedy: DEALERS WILL INSTALL AN INSULATOR BEHIND THE CURRENT SEAT BACK. OWNER NOTIFICATION BEGAN ON JANUARY 7, 2004. OWNERS SHOULD CONTACT FORD AT 1-800-392-3673.
Component: SEAT BELTS:FRONT:ANCHORAGE
VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET DRIVER'S SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.
Consequence: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.
Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.
Component: SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT
VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND.
Consequence: IF THIS OCCURS WHILE THE VEHICLE IS MOVING, REDUCED STEERING CONTROL COULD OCCUR, INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL REPLACE THE LOWER CONTROL ARM BALL JOINTS (2).
ANYTIME I PUT A HALF A TANK IN GAS IN CAR IT SMELLS BAD IN TRUCK SO WHEN THIS DOES HAPPEN I LOOK IN THE TRUCK,THERE'S THIS FOAM IN THE BACK THAT'S CO BED WITH GAS,N THE SMALL IS BAD.I DON'T LET ME KIDS IN THE GAS,NTIL ITS GONE..WILL IT CATCH IN 🔥.IT HAPPENS ALL THE TIME SINCE I BOUGHT THE CAR.HELP PLZ
THE CAR LEAKS ANTI-FREEZE THROUGHT THE PLASTIC MANIFOLD. WHO EVER HEARD OF A PLASTIC MANIFOLD. THE ORIGINAL PART IS A DEFECTIVE PART-MADE OF THE WRONG MATERIAL.FORD NEEDS TO RECALL THIS PART, IT CAUSES HAVIC CONSTANTLY NEEDS TO ADD COOLANT. THE THERMOSTAT CANNOT BE CHANGED BECAUSE THE PLASTIC HOUSING IS ONE PIECE WITH THE MANIFOLD.
I RECEIVED A LETTER SAYING THE LIGHTING SYSTEM WAS RECALLED AND I WAS TO RECEIVE A NOTICE IN THE MAIL AS TO WHEN I COULD COME IN FOR SERVICE. I HAVE NOT RECEIVED THAT SAID NOTICE AND MY LIGHTS ARE NOT REPAIRED.
TIRE FAILURE AT HIGHWAY SPEED. TREAD SEPARATED FROM SIDEWALLS.
ON NUMEROUS OCCASIONS THE SPARK PLUGS HAVE SHOT OUT CAUSING DAMAGE TO THE COIL PACK AND THREADS TO THE BLOCK. THIS IS A 200$ TO 300$ FIX EACH TIME. GETTING TO BE A HASSLE.
TL* THE CONTACT OWNS A 1999 FORD CROWN VICTORIA. WHILE DRIVING AT 50 MPH, THE CONTACT SUDDENLY LOST CONTROL OF THE VEHICLE. THE CONTACT WAS ABLE TO ENGAGE THE BRAKE PEDAL IN ORDER TO STOP THE VEHICLE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC, WHO DIAGNOSED THAT THE BALL JOINT FRACTURED. THE VEHICLE WAS REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 83,000.
DEFECTIVE INTAKE MANIFOLD IS WAS MADE OF A CHEAP PLASTIC.. *TR
UNDER NORMAL DRIVING CONDITIONS AT APPROXIMATELY 25 MPH I BEGAN TO SMELL A SWEET BURNING SCENT THAT I QUICKLY RECOGNIZED AS COOLANT. I PULLED OVER & INSPECTED THE ENGINE COMPARTMENT. THE FIRST THING I OBSERVED AFTER REMOVING THE PLASTIC FACIA FROM THE TOP OF THE ENGINE WAS A CRACK IN THE WATER TEMPERATURE SENSOR HOUSING RIGHT IN FRONT ON THE TOP PASSENGER SIDE OF THE INTAKE MANIFOLD. I WAS LESS THAN A BLOCK FROM MY HOME SO I DROVE HOME AND HAD IT TOWED INTO HARVEY'S AUTO THE NEXT DAY. [XXX] HAS TOLD ME THAT THERE WAS A RECALL ON THIS INTAKE MANIFOLD AND AS THE ORIGINAL OWNER I SHOULD HAVE BEEN NOTIFIED ABOUT THIS RECALL. I WAS NEVER INFORMED OF ANY RECALLS. [XXX] PLACED A TEMPORARY WELD WHICH HAS HELD UP JUST FINE, HOWEVER HE SAID THAT THERE ARE SEVERAL OTHER ISSUES WITH THE STRUCTURAL INTEGRITY OF FORDS ORIGINAL DESIGN AND THAT ULTIMATELY THE MANIFOLD WILL FAIL AT THESE WEAK POINTS WITH TIME. I DON'T PUT HEAVY MILES ON MY VEHICLE & ONLY HAVE 41,102 MILES ON IT NOW. ALL SERVICES HAVE BEEN PERFORMED AT 3000 MILE INTERVALS FROM AUTHORIZED MECHANICS. I HAVE ALL RECEIPTS OF MY SERVICE RECORDS AND FEEL THAT THE ONLY REASON I DIDN'T EXPERIENCE A FAILURE EARLIER IS BECAUSE OF MY DILIGENT EFFORTS TO FOLLOW THE RECOMMENDED SERVICE INTERVALS SET FORTH IN THE VEHICLES MAINTENANCE LOG. I FEEL THAT IT WAS AND STILL IS THE RESPONSIBILITY OF FORD TO SEEK OUT ALL OWNERS UNTIL EACH VEHICLE HAS BEEN REPAIRED. THE OF RECALL EXPIRED IN 2009 ACCORDING TO FORD CUSTOMER SERVICE BUT I FEEL THAT THERE SHOULD HAVE BEEN MORE EFFORT BY FORD MOTORS TO INFORM ALL OWNERS OF THIS DEFECT. I WOULD APPRECIATE IT IF FORD WOULD ACCEPT RESPONSIBILITY FOR SELLING A KNOWN FAULTY ITEM AND EXTEND AND HONOR THEIR ORIGINAL RECALL REPARATIONS FOR MY VEHICLE. I DID MY PART IN FOLLOWING ALL SERVICE REQUIREMENTS AND THEY SHOULD AS WELL. THANK YOU FOR YOUR ASSISTANCE AND TIME. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR
MY NAME IS [XXX] AND MY FORD CROWN VICTORIA HAS A PROBLEM WITH THE REAR AXLE ASSEMBLY THE C-CLIP KEEPS FALLING OFF THE AXLE SHAFT AND I THINK THIS SHOULD BE A RECALL I'M NOT SURE HOW MANY OTHER PEOPLE EXPERIENCED THIS PROBLEM BUT I AM AND THE REAR END IS TOO EXPIENCIVE TO REPAIR AND I THINK THIS SHOULD BE ADMITTED TO FORD BECAUSE THE AXLE SHAFT IS FAULTY AND THE DIFFERENTIAL 3:55 IS A BAD CONCEPT ON MY CAR I DON'T SPEED OR BEAT MY CAR DOWN OR DOG IT OUT I DRIVE THE SPEED LIMIT AND USE THE CAR AS SUPPOSED TO AND THE OTHER PROBLEM IS THE CAR HAS RANDOM MISFIRES AS WELL THE PROBLEM I INSIST OF COMPLAINING OF CAN CAUSE AN ACCIDENT OR WORSE AND I FEEL FORD SHOULD RECALL THE CAR FOR THIS MAJOR PROBLEM PLEASE CONTACT ME IF YOU CAN HAVE SOMETHING DONE ABOUT THESE PROBLEMS. 'PARTS OF THIS DOCUMENT HAVE BEEN REDACTED TO PROTECT PERSONALLY IDENTIFIABLE INFORMATION PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).' *TT
MY PARENTS PICKED MY DAUGHTER UP FROM THE SCHOOL BUS AND PROCEEDED DOWN MY DRIVEWAY SLOWLY. THE VEHICLE SUDDENLY ACCELERATED EVEN AS MY FATHER HAD BOTH FEET ON THE BRAKE. THERE WERE VISIBLE SIGNS OF THE FRONT WHEELS DRAGGING UP DEBRIS AS THE FRONT WHEELS WERE LOCKING UP. HE ATTEMPTED TO SHIFT INTO NEUTRAL AND TURN THE KEY BUT WAS UNABLE TO DO SO AS THE VEHICLE MUST HAVE REACHED A SPEED IN EXCESS OF 50 MPH BEFORE HE SLAMMED IT INTO PARK AND THEN RAN HEAD ON INTO A TREE. BOTH PARENT WERE INJURED SEVERELY EVEN WITH THE AIR BAGS DEPLOYING. THE CAR WAS DESTROYED. *TR
MY INTAKE MANIFOLD WENT BAD. THIS IS A KNOWN ISSUE AND A LAWSUIT WAS FILED. IT COST ME $1,600 AND FORD WON'T REIMBURSE ME. *JS
Showing 15 of 164 complaints