NHTSA recalls, safety ratings, and consumer complaints for the 2009 Mazda Mazda6.
| Overall Rating | Not Rated |
| Frontal Crash | Not Rated |
| Side Crash | Not Rated |
| Rollover | Not Rated |
Component: SUSPENSION:FRONT:CONTROL ARM
Mazda North American Operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The front cross member may corrode after exposure to road salt.
Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.
Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began March 18, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I.
Component: AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE
Mazda North American Operations (Mazda) is recalling certain 2007-2012 CX-7, CX-9, and 2009-2012 Maza6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began December 3, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317F. Note: This recall supersedes recalls 16V356 and 17V012.
My rear subframe rusted thru and has holes in it. It is too dangerous to drive and mazda won't recall the rear like the front subframe knowing that a lot of people are suffering from the same issue. A subframe should last a long time. My mechanic inspected the car and feels like it's not safe to drive.
This car was purchased in 2017 and maintenanced regularly. We recently took it to have the oil changed and to check out a noise that was coming from the passenger side. We were told that the subframe was rusted so badly it was too dangerous to drive and would cost $7k to repair. That caught us by surprise and we ended up having to buy a car by the next day. We traded the car in… However, I started doing some research and noted that this is very common and there was a recall between 2010 and 2014. I’m pretty upset that we lost this car without having any recall notification after the purchase. Could this have been taken care of instead of having to get a new car?
Component or System that Failed: The front subframe on my 2009 Mazda 6i Touring is completely rusted through. There are holes in the frame and large flakes of rusted metal breaking off. The car is available for inspection if needed. Safety Risk: This is a serious safety concern because if the subframe fails, I could lose steering or suspension control while driving. That would put me and other drivers at immediate risk of an accident. Reproduction / Confirmation: An independent mechanic confirmed the problem and told me the car is unsafe to drive in its current condition. Inspection: The vehicle had the original Mazda subframe corrosion recall performed years ago, but now the same exact problem has come back. The car has not yet been re-inspected by Mazda, but the severity of the rust is obvious. Warning Lamps / Symptoms: There were no warning lights or messages before this happened. The issue was only noticed when the rust and holes became visible on the underside of the car during a recent inspection.
The 2009 Mazda Mazda6 has 10 NHTSA recalls and 384 consumer complaints on file. It received an overall safety rating of Not Rated out of 5 stars in NHTSA crash testing. The high number of complaints suggests potential reliability concerns — review the complaint details above before purchasing. For the most detailed information about a specific vehicle, decode its VIN using our free decoder above.
Enter a specific VIN to get the full report — specs, recalls, safety ratings, complaints, investigations, and technical service bulletins.
Component: AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE
Mazda North America Operations (Mazda) is recalling certain 2009-2011 Mazda6, and 2007-2011 CX-7 and CX-9 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the passenger frontal air bag inflator with an alternate inflator, free of charge. The recall began on August 30, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 16V356 and all vehicles that were not remedied under that campaign are now covered by this one.
Component: AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE
Mazda North American Operations (Mazda) is recalling certain 2013 Mazda6 and CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2010 Mazda6, CX-7 and CX-9 vehicles sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2009 Mazda6, CX-7, and CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began March 2, 2018. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F.
Component: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE
Mazda North American Operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured February 4, 2008, to December 3, 2009. The protective coating may not have been properly applied to the air bag control unit (ACU) and, as a result, moisture may damage the unit causing it to malfunction.
Consequence: Failure of the ACU would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.
Remedy: Mazda dealers will replace the ACU, free of charge, however parts are not currently available. The recall began June 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816H.
Component: AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE
Mazda North America Operations (Mazda) is recalling certain 2012 CX-7, CX-9 and Mazda6 vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Mazda is recalling certain 2009 CX-7, CX-9 and Mazda6 vehicles sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Mazda is recalling certain 2007-2008 CX-7 and CX-9 sold, or ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the front passenger side air bag inflator with an alternate inflator, free of charge. The recall began October 4, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 17V-012.
Component: LATCHES/LOCKS/LINKAGES:DOORS:LATCH
Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured February 4, 2008, through August 24, 2012. The door latch mounting screws may become loose.
Consequence: If all three door latch mounting screws become excessively loose the door latch mechanism would not engage and the door might open while the vehicle is in motion increasing the risk of accident or injury.
Remedy: Mazda will notify owners, and dealers will apply a thread locking adhesive to the door screws and retorque them, free of charge. The recall began on October 29, 2013. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number is 7013I.
Component: FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY
MAZDA IS RECALLING CERTAIN MODEL YEAR 2009-2010 MAZDA6 VEHICLES MANUFACTURED FROM APRIL 8, 2008, THROUGH FEBRUARY 8, 2010. A CERTAIN TYPE OF SPIDER MAY WEAVE A WEB IN THE EVAPORATIVE CANISTER VENT LINE AND THIS MAY CAUSE A RESTRICTION IN THE LINE. IF THIS OCCURS, THE FUEL TANK PRESSURE MAY BECOME EXCESSIVELY NEGATIVE WHEN THE EMISSION CONTROL SYSTEM WORKS TO PURGE THE VAPORS FROM THE CANISTER.
Consequence: AS THE CANISTER IS PURGED REPEATEDLY DURING NORMAL OPERATION, THE STRESS ON THE FUEL TANK MAY EVENTUALLY RESULT IN A CRACK, POTENTIALLY LEADING TO FUEL LEAKAGE AD AN INCREASED RISK OF FIRE.
Remedy: DEALERS WILL INSPECT AND CLEAN UP THE CANISTER VENT LINE, AND INSTALL A SPRING TO PREVENT THIS TYPE OF SPIDER FROM ENTERING THE VENT LINE. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE MARCH 25, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Component: STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS
MAZDA IS RECALLING 29,000 MY 2009 MAZDA6. THE OUTER DOOR HANDLES MAY STICK WHICH MAY PREVENT THE DOOR FROM LATCHING. THIS SITUATION MAY ALLOW THE DOOR TO OPEN WHILE THE VEHICLE IS IN MOTION.
Consequence: DRIVING THE VEHICLE WITH THE DOOR UNLATCHED COULD LEAD TO AN UNBELTED OCCUPANT BEING EJECTED AND COULD RESULT IN DEATH OR INJURY.
Remedy: DEALERS WILL INSPECT THE DOOR HANDLES AND IF NECESSARY REPAIR OR REPLACE THE HANDLES FREE OF CHARGE. THE RECALL BEGAN ON FEBRUARY 13, 2009. OWNERS MAY CONTACT MAZDA AT 1-800-222-5500.
Component: EQUIPMENT
THULE, INC. IS RECALLING 2,323 OWNER-INSTALLED ROOF-MOUNTED FIT KITS, MODELS 3068 AND 3069, MANUFACTURED BETWEEN JANUARY 1, 2008 AND FEBRUARY 28, 2009 THAT ARE USED WITH THULE PODIUM FOOT PACKS, MODELS 460 AND 460R. THESE FIT KITS WERE SOLD AS AFTERMARKET EQUIPMENT FOR USE ON THE VEHICLES LISTED ABOVE. THE BOLT(S) USED TO SECURE THE FOOT TO THE VEHICLE WAS MANUFACTURED TO A HARDNESS THAT MAY CAUSE THE BOLT(S) TO BE BRITTLE AND POTENTIALLY BREAK UNDER STRESS.
Consequence: THIS MAY RESULT IN THE BOLT(S) SNAPPING OFF DURING USE OR WITHOUT A LOAD. THE UNSECURED RACK AND LOAD CAN THEN COME LOOSE WHILE DRIVING CREATING A POTENTIAL ROAD HAZARD, POSSIBLY RESULTING IN A VEHICLE CRASH.
Remedy: THULE WILL MAIL A RETRO FIT KIT ALONG WITH REPAIR INSTRUCTIONS TO OWNERS FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE APRIL 13, 2009. OWNERS MAY CONTACT THULE TOLL-FREE AT 1-800-238-2388.
Hello, My name is [XXX] . I took our Mazda 6 in for wheel balance and alignment and was informed of very serious rust issues in the rear suspension. I was pretty shocked at what they showed me. I worked at Raben Tire for 10 years and I've never seen anything like this. I have two retired mechanic friends look at it, and they (along with the mechanic from firestone) said they cannot even fathom how this level of rust is possible (80+% of the miles on this vehicle are highway). One of my retired mechanic friends started looking into it and said he'd noticed the 09 Mazda recalls for suspension rust. We all thought that made sense given how immensely abnormal this rusting is. The recall list sent to me says "front" suspension. I'm not sure why the front is listed and not the rear, but this, to all of us, is very clearly faulty (the rusting is INCREDIBLY abnormal) and we believe should be considered as part of the suspension rust recall (there are no rusting issues anywhere else). Ive provided pictures. This is incredibly unsafe. The rear suspension could collapse at any moment while driving and cause casualties. Thank you for your time, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The front and rear crossmembers have significant rust. The front has holes and chunks of metal missing due to rust corrosion. The rear has flaking and is deeply pockmarked with rust. These are structural components. Failure can lead to a crash.
The passenger crash pad has deteriorated and become sticky and cracked. This may affect deployment of airbag and perhaps allow outside environmental elements to affect the airbag. The takata fiasco being an example of environmental factors affecting airbag safety.
The rear Suspension Frame has failed due to corrosion. The right rear tire has worn severely from the premature failure of that part on the right side. I feel it was a defect in Engineering by Mazda. My email: [XXX] Mobile: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The rear frame has failed due to corrosion on the right side. The rear passenger tire is canted in on the topside worn severely worn. This was noted when I drove home from my job. This is a critical part of the vehicle and should've never failed. I'm hopeful to hear from the NHTSB for a repair to be done properly by Mazda;
Rear suspension cross-member corroded to the point that a minor pothole separated the right lower control arm mounting point from the cross-member, rendering the car undrivable. The rest of the car is fairly rust-free.
Rear subframe corrosion
Vehicle jerks at low speed when accelerate and idle when accelerate, P0766 Code shows, engine noise and gears jump, when reverse the vehicle jerks.
2009 Mazda 6 Rear subframe and springs are deemed unsafe due to extreme rusting and corrosion. The vehicle is registered and has been registered in both NY and PA (salt states), however was regularly washed and garage maintained. Vehicle will no longer pass inspection due to this issue and Mazda indicates no recall for the rear at this time and is ignoring that this is a highly prevalent issue. Mazda recalled and acknowledged this issue on these makes/models related to the front; however refuses to acknowledge and repair/recall the issue extending to the rear. The vehicle is in otherwise good shape, and the extreme rusting to the subframe/springs is not consistent with normal wear and tear. This is an extremely prevalent issue arising to these vehicles being ignored by Mazda. Mechanics are indicating the issue is extremely deteriorated and not safe, but that the vehicle is in otherwise good shape and the issue is consistent with faulty parts.
The sensors on my alarm system will randomly activate, with alarm going off at 30 second intervals. The problem began approximately 6 months ago. I took the initiative to replace my cars battery, along with the battery in my fab. I really thought that solved my problem, as a first step fix. I began once again to identify the sound of my car alarm in multiple parking lots throughout time. I have been investigating this problem, and have read that this alarm problem has been sited by many Mazda 6 owners. I am the original owner of the 2009 Mazda 6 Grand Touring, and have 67,000 miles driven. I called the Repair Department at my dealership, and was told that it cost $185.00 for just the diagnosis. My auto insurance company policy price is based on using a secured vehicle. Right now I only can leave it unlocked in my garage, otherwise, my vehicle is at risk of being stolen.
This 2009 Mazda 6 hit a chuck hole in the Buffalo NY area, virtually severing the connection between the rear cross member (aka cradle or sub frame) and the right rear wheel and rendering the car all but undriveable. Mechanic said the failure to sufficiently rust proof the subject parts caused severe deterioration of the rear sub frame. This is essentially the same problem that led NHTSA to issue a recall on this vehicle for the front engine cradle in 2018.
I noticed a rattling sound that seemed to come from the rear passenger side wheel. I took it to a mechanic who told me that the rear sub-frame was so rusted that the damper had come loose from the sub-frame and caused the rattling sound. He said that he was unable to reattch the damper because the sub-frame was too rusted. The only solution was to remove the loose damper to eliminate the rattling sound and continue driving that way OR have the rear sub-frame replaced which would cost from $4,000-$6,000.
Showing 15 of 384 complaints