Loading vehicle data from NHTSA...
NHTSA recalls, safety ratings, and consumer complaints for the 2019 BMW X5.
| Overall Rating | |
| Frontal Crash | |
| Side Crash | |
| Rollover |
Component: EQUIPMENT:OTHER:LABELS
BMW of North America, LLC (BMW) is recalling certain 2019 BMW X5 xDrive40i and X5 xDrive50i vehicles. The driver and/or passenger sun visor may have an incorrect air bag warning label, or the label may be missing. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant crash protection."
Consequence: Without a label that shows the proper restraint usage guidelines, the occupants may have an increased risk of injury in the event of a crash.
Remedy: BMW notified owners, and dealers will inspect the driver and passenger sun visor, replacing the visors as necessary, free of charge. The recall began January 4, 2019. Owners may contact BMW customer service at 1-800-525-7417.
Component: FUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP
BMW of North America, LLC (BMW) is recalling certain 2020 750i xDrive, 2019 M850i xDrive Coupe, M850i xDrive Convertible, X5 xDrive50i, X7 xDrive50i, and M5 vehicles. The high pressure fuel pump may not have been properly attached to the engine, which may cause the fuel pump flange to crack, resulting in a fuel leak.
Consequence: A fuel leak in the presence of an ignition source can increase the risk of a fire.
Remedy: BMW will notify owners, and dealers will replace the high pressure fuel pumps, free of charge. The recall began August 27, 2019. Owners may contact BMW customer service at 1-800-525-7417.
Component: ELECTRICAL SYSTEM
BMW of North America, LLC (BMW) is recalling certain 2019 BMW X5 xDrive40i vehicles. The capacitors within the Body Domain Controller (BDC) may short circuit and overheat.
Consequence: If the BDC short circuits, other nearby components may also overheat, increasing the risk of a fire.
The starter on my BMW failed, and it overheated and damaged my alternator to the point that I needed to replace it. The dealer and independent service center confirmed that this was the cause, but BMW is refusing to reimburse the cost of the alternator replacement. I was at the exit of a highway and could not even put the car in neutral, so my safety was significantly at risk.
The contact owns a 2019 BMW X5. The contact stated that while driving at an undisclosed speed, the vehicle unexpectedly overheated, and the engine temperature warning light illuminated. The vehicle was taken to a dealer, where it was diagnosed that the coolant line to the cylinder had failed and needed to be replaced. The vehicle was repaired. The contact later received notification of NHTSA Campaign Number: 25V644 (Electrical System). The manufacturer was not made aware of the failure. The approximate failure mileage was 101,187.
The AC evaporator failed due to a known manufacturing defect common across the BMW G-chassis platform (G05, G07, G30). This has created two severe safety hazards: The refrigerant leak causes the windshield to fog up instantly and unexpectedly while driving, completely obstructing my visibility and nearly causing an accident. Chemical fumes and oil from the leaking evaporator are entering the cabin through the vents, causing dizziness and respiratory irritation for the occupants. BMW is aware of this systemic issue through numerous owner reports and petitions but refuses to issue a recall or provide assistance. This is a critical component failure that directly impacts vehicle safety and occupant health.
The 2019 BMW X5 has 13 NHTSA recalls and 161 consumer complaints on file. It received an overall safety rating of 4 out of 5 stars in NHTSA crash testing. The high number of complaints suggests potential reliability concerns — review the complaint details above before purchasing. For the most detailed information about a specific vehicle, decode its VIN using our free decoder above.
Enter a specific VIN to get the full report — specs, recalls, safety ratings, complaints, investigations, and technical service bulletins.
Remedy: All affected vehicles remain on dealer lots, therefore owner letters will not be mailed. BMW dealers will replace the BDC control unit, free of charge. The recall began on October 17, 2018. Owners may contact BMW customer service at 1-800-525-7417.
Component: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA
BMW of North America, LLC (BMW) is recalling certain 2019-2021 X3 sDrive30i, X3 xDrive30i, X3 M40i, X3M, X4 xDrive30i, X4 M40i, M550i, X4M, X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5M, X5 M50i, X7 xDrive40i, X7 xDrive50i, X7 M50i, Alpina XB7, 330i, 330i xDrive, M340i, M340i xDrive, and 8 Series Coupe, Convertible and Grand Coupe, 840i, 840i xDrive, M850i xDrive, M8, 2020-2021 530e, 530e xDrive, 330e, 330e xDrive, 745Le, 745Le xDrive, X5 xDrive45e, X3 xDrive30e, X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6 M50i, X6M, 530i, 530i xDrive, 540i, 540i xDrive, M550i xDrive, M5, 740i, 740Li, 740Li xDrive, M760i Drive, M760Li xDrive, 750Li xDrive Alpina, Alpina B7 xDrive, and 2021 4 Series Coupe 430i, 430i xDrive, M440i xDrive vehicles. When shifting into Reverse, a small portion of the rearview image may be obscured, or the screen may not illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rear Visibility."
Consequence: If the driver relies on only the rearview camera image, the missing or reduced rearview image view can increase the risk of a crash or injury.
Remedy: BMW will notify owners, and dealers will inspect the rearview camera software and update it if necessary, free of charge. The recall began April 16, 2021. Owners may contact BMW customer service at 1-800-525-7417.
Component: WHEELS:LUGS/NUTS/BOLTS/STUDS
BMW of North America, LLC (BMW) is recalling certain 2019 X5 xDrive50i and X7 xDrive40i vehicles. The left side wheel bolts may have been insufficiently tightened and may loosen over time.
Consequence: Loose bolts may allow a wheel to detach from the vehicle, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace and tighten the left side wheel bolts, free of charge. The recall began July 16, 2019. Owners may contact BMW customer service at 1-800-525-7417.
Component: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA
BMW of North America, LLC (BMW) is recalling certain 2018 540d, 2018-2020 530i, 530i xDrive, 540i, 540i xDrive, M550i xDrive, M5, 530e, 530e xDrive, X3 sDrive, X3 xDrive, X3 M40i, X3 M, and 2019-2020 X4 xDrive, X4 M40i, X4 M, X7 xDrive, X7 M50i, 740Li, 740Li xDrive, 750Li, 750Li xDrive, 8 Series Convertible and Coupe 840i, 840i xDrive, M850i xDrive, X5 sDrive, X5 xDrive, X5 M50i, X6 xDrive, X6 M50i, 330i, 330i xDrive, M340i, M340i xDrive, Z4 sDrive, Z4 M40i, 740Le xDrive and 745Le xDrive, 2018-2019 640i xDrive Gran Turismo and Rolls-Royce Phantom, 2019 M850i xDrive Gran Coupe and Rolls-Royce Cullinan and 2020 Toyota Supra vehicles. The back-up camera and display settings can be adjusted such that the rear view image is no longer visible and the system will retain that setting the next time the vehicle is placed in reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rearview Mirrors."
Consequence: The lack of an image in the back-up camera display increases the risk of a crash.
Remedy: BMW will notify owners, and dealers will update the back-up camera software, free of charge. The recall began November 8, 2019. Owners may contact BMW customer service at 1-800-525-7417 or Rolls-Royce at 1-877-877-3735. Toyota owners may contact Toyota customer service at 1-888-270-9371.
Component: STEERING
BMW of North America, LLC (BMW) is recalling certain 2019-2020 X5 sDrive40i, X5 xDrive40i and X5 xDrive50i vehicles and 2020 X6M vehicles. The steering column shaft bearing plate may not have been properly attached to the vehicle, allowing it to loosen.
Consequence: A loose bearing plate can affect the vehicle's handling and control, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will inspect the steering column shaft bearing plate and properly attach or replace it, as necessary, free of charge. BMW telephoned owners and all of the vehicles have been remedied. No owner notification letter is necessary. Please contact BMW customer service at 1-800-525-7417.
Component: SERVICE BRAKES, HYDRAULIC
BMW of North America, LLC (BMW) is recalling certain 2020-2021 8 Series Coupe, Grand Coupe and convertible 840i, 840i xDrive, M850i xDrive, M8 and 740 Li, 740 Li xDrive, 750 Li xDrive, M760 Li xDrive, X6 sDrive40i, X6 xDrive40i, X6 xdrive50i, X6 M50i, X6M, and 2019-2021 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M, X7 xDrive40i, X7 xDrive50i, X7 M50i, and 2021 M3, M3 Competition, M4 Coupe, M4 Competition Coupe, X5 xDrive45e, 745 Le xDrive. The rotor and shaft within the integrated brake system may not have been welded properly and could separate during a hard braking event, possibly resulting in a loss of the Antilock Brake System (ABS) and braking assistance.
Consequence: A loss of ABS and a reduction in braking assistance can increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the integrated brake system, free of charge. Owner notification letters were mailed on May 25, 2021. Owners may contact BMW customer service at 1-800-525-7417.
Component: SEATS
BMW of North America, LLC (BMW) is recalling certain 2019 X5 xDrive40i and xDrive50i vehicles. The attachment bolts for the driver's seat and/or seat belt may not have been properly tightened.
Consequence: The improperly tightened bolts can increase the risk of injury in the event of a crash.
Remedy: BMW will notify owners, and dealers will inspect the attachment bolts for the driver's seat and seat belt, and torque them to the correct specifications, as necessary, free of charge. The recall began April 9, 2019. Owners may contact BMW customer service at 1-800-525-7417.
Component: AIR BAGS:FRONTAL
BMW of North America, LLC (BMW) is recalling one 2019 X5 xDrive 40i vehicle. The instrument panel may not have been manufactured correctly, which could prevent the passenger side air bag from deploying properly in a crash.
Consequence: An air bag that does not deploy properly can increase the risk of injury in a crash.
Remedy: A dealer will replace the instrument panel, free of charge. Owner notification letters were mailed on July 26, 2021. Owners may contact BMW customer service at 1-800-525-7417.
Component: VISIBILITY:SUN/MOON ROOF ASSEMBLY
BMW of North America, LLC (BMW) is recalling certain 2022 4 Series Gran Coupe (430i, 430i xDrive, M440i xDrive); 2019-2022 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M; 2021-2022 X5 xdrive45e; 2020-2022 X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6M and 2019-2023 X7 xDrive40i, X7 xDrive50i, X7 M50i, X7 xDrive60i, X7 M60i, X7M, Alpina XB7 vehicles. The roof function control unit may be programmed incorrectly, allowing the sunroof to close without the key fob present inside the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 118, "Power-Operated Window Systems."
Consequence: A sunroof that closes without the key fob present inside the vehicle can increase the risk of injury.
Remedy: Dealers will reprogram the roof function control unit, free of charge. Owner notification letters were mailed June 20, 2022. Owners may contact BMW customer service at 1-800-525-7417.
Component: ELECTRICAL SYSTEM:STARTER ASSEMBLY
BMW of North America, LLC is recalling certain 2019-2020 X5, X7, 2020 3 Series Sedan, X6, 2020-2021 7 Series Sedan, 2020 8 Series Convertible, 8 Series Coupe, and 2020 8 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. In the event the starter motor fails, repeated attempts to start the vehicle can cause the starter motor to overheat from an electrical overload.
Consequence: A starter motor that overheats can ignite nearby combustible material in the engine compartment, increasing the risk of a fire.
Remedy: Dealers will update the vehicle software, free of charge. Owner notification letters were mailed September 27, 2024. Owners may contact BMW customer service at 1-800-525-7417.
Component: ELECTRICAL SYSTEM:STARTER ASSEMBLY
BMW of North America, LLC (BMW) is recalling certain 2020 340I, X6, 2020-2025 840I, 2020-2022 740LI, 2019-2020 X7, and X5 vehicles. After repeated attempts, the starter motor may overheat from an electrical overload.
Consequence: An overheated starter motor can ignite nearby combustible material in the engine compartment, increasing the risk of a fire.
Remedy: Dealers will replace the engine starter, free of charge. This recall includes vehicles repaired under recall 24V576 and those owners will need to have their vehicle repaired again. Owner notification letters were mailed February 9, 2026. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov November 17, 2025.
I am writing to report a significant safety issue associated with BMW vehicles equipped with the B58TU engine, particularly the 2019-2021 models. These vehicles feature an oil pump containing an internal plastic component responsible for regulating oil pressure. There have been numerous instances of this part fracturing in the field, leading to a sudden loss of oil pressure. The failure predominantly occurs during cold starts in low temperatures. When this occurs, oil pressure can fluctuate erratically or be lost completely, often with minimal warning. Potential warning signs include difficulties in electronically measuring the oil level, abnormal oil pressure readings, or sudden drivetrain malfunction alerts. These issues can escalate quickly, resulting in engine shutdown or severe damage due to oil starvation. This situation poses a serious risk, as the vehicle may become inoperable without warning while driving or immediately after startup. Such failures are particularly hazardous when vehicles become immobilized in traffic or during winter conditions, leaving occupants vulnerable to harsh temperatures while awaiting roadside assistance. The replacement of the oil pump necessitates extensive disassembly and typically incurs a cost of $6,000-$8,000, assuming no engine damage has occurred. A significant concern is that owners cannot easily ascertain whether their vehicle is equipped with the original plastic pump or a revised metal component. BMW's VIN-based parts lookup now indicates updated components even if the original plastic parts are still installed. Additionally, the original plastic part number has been removed from dealer networks. Failures have been reported across multiple production years, and the full extent of affected vehicles remains uncertain. Given that this condition can lead to abrupt vehicle disablement without adequate warning—especially in cold weather—this situation warrants investigation as a potential safety-related defect.
I bought the car from the dealership, and they said there were no problems with it, but they cheated me. The car broke down twice. The first time, it was parked in a private lot for several hours, and I paid a large sum for parking. The second time, it broke down on the street, and I waited eight hours for help to tow it back to the dealership. 1-recall message 2- emergency call system
Subject: 2019 BMW X5 xDrive40i – Oil Pump Defect Causing Oil Measurement Failure and Safety Risk I am reporting a safety defect in my 2019 BMW X5 xDrive40i with the 3.0L B58 inline-6 engine. The vehicle currently has approximately 70,000 miles. The vehicle is unable to properly measure or display engine oil level due to incorrect oil readings, which have been attributed to a failing oil pump assembly containing internal plastic components. Because this vehicle does not have a traditional dipstick, the electronic oil level monitoring system is the only way to verify proper oil level. Due to the defective oil pump design, I am unable to confirm whether the engine has sufficient oil. This creates a serious safety concern because: •The vehicle may be operating with low oil pressure without accurate warning •Sudden oil pressure loss could cause engine shutdown while driving •Loss of power at highway speeds could result in an accident •Catastrophic engine failure could occur without proper oil monitoring This is not normal wear and tear. BMW has reportedly updated the oil pump design in newer model years to use metal internal components, suggesting awareness of a design weakness. However, no recall has been issued for 2019 models. An oil pump that prevents accurate oil level measurement and may fail prematurely presents a significant safety hazard. I respectfully request that this defect be formally investigated and that BMW be required to issue a recall to replace the defective oil pump assembly with the updated metal design.
The contact owns a 2019 BMW X5. The contact stated that while driving approximately 45 MPH, the red oil light suddenly illuminated and the messages "Stop Carefully and Turn Off Engine", “Engine Oil Pressure Too Low", "Continued Driving will Result in Engine Damage". The vehicle was towed to the local mechanic, who discovered that the engine oil was black and thick. The vehicle was later towed to the local dealer, who confirmed that the engine oil was thick and dark, and the engine needed to be replaced. The failure mileage was 85,000.
BMW knowingly did NOT NOTIFY it's 2019 BMW X5 M40i (engine B58) vehicle owners. This is in reference to the faulty design and made plastic engine oil pump. It has been known to fail prematurely due to weaken parts. Some analysis done was from certain oil viscosity's applying additional unneeded stressful pressures. This later was recognized by BMW and a newer design and/or metal sturdier one had taken it's place in subsequent model years starting in 2020. Some owners were able to remediate the oil pump failure and new replacement either covered under intact warranties, and some were covered through quieter negotiations with BMW Customer Care's authorizations. To my understanding, no recalls were made nor were any techical service bulletins (TSB) made to it's owners. I don't see how BMW can be allowed to get away with an issue of safety which could cause a catastrophic failure of the affected engine? Under the circumstances, BMW should be fully reimbursing me for the repairs here, and be glad there were NO serious injuries OR worse, DEATHS! I have been in contact with their Customer Care and nothing has been done to date.
Premature oil pump failure. 2019 BMW x5 with only 46k miles has been diagnosed with an oil pump failure. Vehicle needed to be quickly pulled over and shut off to avoid catastrophic engine failure or engine seize. If this happens on the highway or at any speed the vehicle will lose power and be unsafe to control likely ending in an accident. This is a known Issue. BMW produced the vehicle with a flawed oil pump design that has a plastic ring around the impeller. The ring deteriorates and cracks leading to pump failure and loss of oil pressure It is only on limited models early 2019 X5. BMW redesigned with an all metal pump quietly. This issue needs to be addressed with BMW as it is unsafe for these family vehicles to be on the road with such a significant risk to its passengers and others. The failure happens with little to no warning. When contacting BMW they told me they would not consider helping with repairs. The repair for this part is upward of $8k which in turn will likely limit consumers ability to fix proactively. This is totally unacceptable and needs to be addressed by the NHTSA directly with BMW. P
The engine warning system came on and warned of low oil pressure. Knowing the oil level was good I stopped the vehicle to check oil leaks. Found none. Knowing engine mechanics I assumed it was a faulty oil pump. had it towed to BMW and told it was so. The replacement would be $8,000. Found out after lengthy research that the oil pump of the 2019 X5 (which I have) was made with plastic internal parts that would be a matter of when not if, the plastic parts would fail because the acidic nature of used oil. Presented this info to BMW and they lowered the price to $3986.16. Then I discovered BMW knew about the problem and changed the oil pump design from 2020 on.
Engine Starter overheating. Car won't start until engine cools down. Car would not let my shift into neutral in order to move to a safe location. Was stuck in front of several cars in an unsafe location. No warning message showed up. Car was just inspected and serviced with no indication that this was a problem. Car taken to dealer after incident and inspected produced the same results.
Car randomly wouldn’t start and was getting error starter message on message center
The emergency call system and hands free microphone does not work due to the telematic control unit getting wet as a result of the shark fin antenna leaking. As a result I cannot rely on communication through this system in the event of an emergency which was one of the features that lead me to the decision to buy this car. The vehicle has been inspected by the dealer. The first warning lamp brought to the attention of the dealer in February.
Transfer case on 2019 X5,yes available for inspection upon request. At stop position making right turn or left turn the vehicle jutters,also in reverse. Yes - confirmed by the bmw service center who tried to charge for diagnostic fee. Manufacturer knows of issue on 2019 X5 models. Video of these transfer case issues all over online in videos. Issue started about 6 - 9 months ago.
Parking brakes can only be applied but cannot be released due to faulty design of the parking switch. This will cause the vehicle not able to move or be towed in an emergency especially when an engine failed to start. This problem confirmed by an independent repair shop and also has highlighted in several BMW group chats.
Showing 15 of 161 complaints